None HSB-24 Manual de Utilização e Manutenção Página 1

Consulte online ou descarregue Manual de Utilização e Manutenção para Aquecedores elétricos None HSB-24. none HSB-24 Use and Care Manual Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
Vista de página 0
THIS MANUAL IS THE PROPERTY OF THE OWNER.
PLEASE BE SURE TO LEAVE IT WITH THE OWNER WHEN YOU LEAVE THE JOB.
1-550.28
5H0707180000
September, 2014
INSTALLATION AND SERVICE MANUAL
steam/hot water unit heaters
Inspection On Arrival
1. Inspect unit upon arrival. In case of damage, report it
immediately to transportation company and your local factory
sales representative.
2. Check rating plate on unit to verify that power supply meets
available electric power at point of installation.
3. Inspect unit received for conformance with description of
product ordered (including specifications where applicable).
General Information
Installation and service instructions in this manual are applicable
to the three types of steam/hot water unit heaters which should
be installed in their proper applications for their most effective
function as overhead heating units.
The copper coils are warranted for operation at steam or
hot water pressures up to 150 lbs. per sq. in. gauge, and
or temperatures up to 375°F, cupronickel tube units are
warranted for operating pressures up to 250 PSI and operating
temperatures up to 400°F. Canadian Standards Association
(CSA) requriements state that explosion-proof units may not
be used with a fluid temperature in excess of 329°F and still
maintain their explosion-proof rating, for national electric code
ignition temperature rating T3B for grain dust.
Motors are designed for continuous duty. They can operate in a
maximum ambient temperature of 104°F (40°C).
The unit heaters are listed by the Canadian Standards
Association as certified and Canadian Registered heat
exchangers CRN OH 9234.5C. *Does not apply to V/PT 952.
Steam horizontal and vertical delivery unit heaters are available
in both standard and low-outlet temperature models. Low outlet
temperature models are recommended primarily for installation
on heating systems with steam pressures of 30 to 150 PSI.
When used at these steam pressures they provide lower outlet
air temperatures for longer heat throw and, because of wider
fin spacing, they are less susceptible to clogging in dusty
atmospheres.
The model number of each unit heater indicates its rated Btu/Hr.
capacity/1000 at 2 lbs. steam pressure and 60°F entering air
temperature. For example an HSB 63 has an output of 63,000
Btu/Hr. at 2 lbs. steam and 60°F entering air.
C
US
®
Model HSB
Horizontal Delivery
Top/Bottom
Inlet/Outlet
Model HC
Horizontal Delivery
Side
Inlet/Outlet
Models V/VN
Vertical Delivery
Model PT/PTN
“Power-Throw”
IMPORTANT
The use of this manual is specifically intended
for a qualified installation and service agency.
A qualified installation and service agency must
perform all installation and service of these
appliances.
CAuTION
Do not remove outlet fan guard from vertical
type unit heaters.
Vista de página 0
1 2 3 4 5 6 ... 15 16

Resumo do Conteúdo

Página 1 - IMPORTANT

THIS MANUAL IS THE PROPERTY OF THE OWNER. PLEASE BE SURE TO LEAVE IT WITH THE OWNER WHEN YOU LEAVE THE JOB. 1-550.285H0707180000September, 2014INSTALL

Página 2 - CAuTION

1-550.2810200°F ENTERING WATER 60°F ENTERING AIR20°F WATER TEMPERATURE DROPHOT WATER PERFORMANCE DATA - STANDARD MODELSTable 10.1 - Performance Data f

Página 3 - UNIT LOCATION / UNIT MOUNTING

1-550.28HOT WATER PERFORMANCE DATA - LOW OUTLET TEMPERATURE MODELS11200°F ENTERING WATER 60°F ENTERING AIR20°F WATER TEMPERATURE DROPTable 11.1 - Perf

Página 4 - UNIT MOUNTING

1-550.2812DIMENSIONAL DATATable 12.1 - Model HSB and HC Dimensions ➀ ➁Horizontal Air Delivery Models — Two Styles D Female Approx. Model

Página 5

1-550.28 Male Connections Approx. Model Fan NPT Shipping Number A B C D E F G Diameter Top Bottom Wt. (lb.) V/VN

Página 6 - OPERATION

1-550.28 Amp Draw by Motor Type, Voltage and Power Code 115/60/1 208/60/1 230/60/1 208/60/3 230/460/3 575/60/3 115/60/1 230/460/60/3

Página 7

1-550.2815SERVICE / TROUBLESHOOTINGFails to Maintain Temperature1. Undersized unit heater, boiler, pump or piping.2. Unit heater operating at low spe

Página 8

Modine Manufacturing Company1500 DeKoven AvenueRacine, WI 53403 Phone: 1.800.828.4328 (HEAT) www.modinehvac.com© Modine Manufacturing Company 2014As M

Página 9

1-550.28SPECIAL PRECAUTIONSTHE INSTALLATION AND MAINTENANCE INSTRUCTIONS IN THIS MANUAL MUST BE FOLLOWED TO PROVIDE SAFE, EFFICIENT AND TROUBLE-FREE O

Página 10

1-550.28UNIT LOCATION1. Units should not be installed in atmospheres where corrosive fumes or sprays are present.2. Be sure no obstructions block air

Página 11 - 1-550.28

1-550.284Figure 4.3 - Horizontal Unit DeliveryFigure 4.3 - Vertical Cone JetFigure 4.4 - Vertical One-Way & Two-Way LouversHHHHH1.31.21.11.0.9.8.7

Página 12 - DIMENSIONAL DATA

1-550.28water systems, include a balancing valve in return line for water flow regulation. A drain valve should also be provided below each unit heate

Página 13

1-550.286Figure 6.1 - Suggested Piping Arrangements ➀Steam SystemsUnit Heater Connection for High Pressure SteamHorizontal Unit Heater Connected toOve

Página 14

1-550.28OPERATION7Connections — Female-type permits direct connection of unit heater to the piping. HC models have copper connectors at side of the un

Página 15 - SERVICE / TROUBLESHOOTING

1-550.2882 lbs. STEAM60° ENT. AIRSTEAM PERFORMANCE DATA - STANDARD MODELS➀ Horizontal units with horizontal louvers open 30° from vertical plane. Ver

Página 16 - COMMERCIAL WARRANTY

92 lbs. STEAM60° ENT. AIRSTEAM PERFORMANCE DATA - LOW OUTLET TEMPERATURE MODELS➀ Horizontal units with horizontal louvers open 30° from vertical plane

Comentários a estes Manuais

Sem comentários